P1PE P3500PWA Hyundai Petrol Engine Pressure Washer

P1PE P3500PWA Hyundai Petrol Engine Pressure Washer

  • Product SKU: P3500PWA
  • Availability: In Stock
£307.99
Hurry! only -2 left in stock!


We wont be beaten on price! See our price promise here.

The P3500PWA is a powerful petrol pressure washer by Position One (P1) Power Equipment. The Pressure Washer is powered by a Hyundai 212cc 4 stroke petrol engine which produces 7hp and 5.6kW of output power. 

This high performance petrol jet washer is perfect for at home and DIY use. If you have a patio or driveway to clean, this is the machine for the job. 

Petrol pressure washer vs electric pressure washer

The table below shows the huge difference in performance between a Hyundai powered petrol pressure washer and typical DIY electric pressure washers on the market. 

Model

P3500PWA

DIY Electric pressure washer

Power

5600w/7hp

1400w to 2000w

Pressure

2990psi/ 206bar

1400psi to 2000psi / 90bar to 140bar

Flow rate

8.7 Litres/minute

5-7 Litres/minute

For a more visual explanation of how a petrol engine powered jet wash is superior to an electric pressure washer, take a look at this video.

The assembly is straightforward and takes just 5 minutes

  1. Insert the stub axles through the wheels and into the holes in the frame and secure with the R-clips. 
  2. The upper handle inserts into the lower frame and is held in place by spring loaded ball connectors.
  3. Fill the engine with 600ml of SAE30 engine oil supplied. (Do not overfill).
  4. Fill the petrol tank with fresh unleaded petrol. (Do not overfill).
  5. Connect the high pressure hose to the pump and trigger gun with the M22 threaded connectors.
  6. Select the nozzle required and push firmly into the lance quick release fitting.
  7. Connect your garden hose to the pump inlet using the quick release garden hose connector supplied.

How to start a Petrol Power Washer

  1. Check engine oil level (must be to the top of the oil filler neck) and fuel level.
  2. Petrol ON/OFF switch to right (ON)
  3. Choke to left (START)
  4. Throttle to middle position
  5. Turn on mains water supply
  6. Hold in trigger on lance
  7. Pull recoil start firmly until engine starts
  8. Move the choke lever to the right (RUN).

Operating the P3500PWA Petrol Power Washer

Do not run the engine without a water supply connected to the pump. The water acts as a coolant and lubricant for the high pressure pump. If there is no mains water supply connected to the pump, it will overheat the seals and valves and cause permanent damage. Always use fresh mains water. If dirty water is used it can cause damage to the internal parts of the high pressure pump.

The three cylinder high pressure axial pump is fitted with a thermal protection safety valve. If the pressure washer is run without the trigger gun being squeezed open and water flowing through the pump, then the water in the pump will recirculate around the pump and heat up. To prevent the pump from overheating and damaging the seals the thermal protection valve will open and discharge the hot water, which is replaced with fresh cool water. If possible, switch the engine off when not pressure washing. This saves fuel and wear and tear.

Select the required nozzle and be sure to push it firmly into the quick release fitting on the lance. For normal pressure washing hold the nozzle about 30cm from the object being pressure washed. To use the detergent function, place the black nozzle in the lance and the pressure washer will draw the liquid detergent from the built in tank. This is a low pressure nozzle, so when the soap has been applied, change back to the high pressure nozzle to finish cleaning.

The Axial pump is driven by a 212cc 7hp Hyundai OHV engine. The OHV engines benefit from low end torque, fuel-saving and emission-cutting OHV technology and a more compact size when compared to an OHC engine.

Warning

Never point the high pressure lance at people or animals. Never operate this petrol pressure washer indoors or in a confined space as petrol engines produce lethal Carbon Monoxide fumes. Always switch the engine off and allow it to cool before refueling. 

Maintenance

Check the engine oil level daily- it can be filled to the top of the oil filler neck with SAE30 or 15w40 engine oil. Oil filler cap (5.2).

After the first 20 hours, then every 100 hours change the engine oil. There is an engine drain bolt at the bottom of the engine (5.1). Drain into a suitable container and dispose of safely following local guidelines. 

The high pressure pump is a sealed for life, maintenance free unit. Change the air filter and spark plug every 100 hours. Check that there are no leaks in the high pressure hose. Always store in a frost free environment. If there is any water left in the pump and it freezes, it can cause major damage to the pump body.

If storing for more than a few weeks, it is advisable to drain the float bowl on the carburettor. This can be done by switching the fuel off and running the pressure washer for a few minutes until it stops. This will prevent the unleaded petrol going off in the carburettor and make it easier to start on next use.

Notes about buying a petrol pressure washer

Don’t be fooled by huge pressure ratings. We know our stuff. We’ve been in the industry for 15 years and can tell you it’s not possible to obtain more than 3000psi continuous pressure from a 6.5hp 196cc to 7hp 212cc engine fitted with an axial pump, unless the flow rate is reduced to such a low level that it is not efficient in real life use. Other sellers may claim a lot higher pressure ratings. Please be careful when selecting your pressure washer. 

 

WARRANTY

This product is covered by a manufacturer warranty of 2 years.



SPECIFICATIONS

Gross Weight (kg) 31.50
Engine Size 212cc
Starting System Recoil
Max Pressure 2990psi/206bar
Flow Rate 8.7L
Box Dimensions H x W x L 549 x 520 x 600
Fully Assembled Dimensions H x W x L 1000 x 500 x 600
Model P3500PWA
Net Weight 31.50




We wont be beaten on price! See our price promise here.

The P3500PWA is a powerful petrol pressure washer by Position One (P1) Power Equipment. The Pressure Washer is powered by a Hyundai 212cc 4 stroke petrol engine which produces 7hp and 5.6kW of output power. 

This high performance petrol jet washer is perfect for at home and DIY use. If you have a patio or driveway to clean, this is the machine for the job. 

Petrol pressure washer vs electric pressure washer

The table below shows the huge difference in performance between a Hyundai powered petrol pressure washer and typical DIY electric pressure washers on the market. 

Model

P3500PWA

DIY Electric pressure washer

Power

5600w/7hp

1400w to 2000w

Pressure

2990psi/ 206bar

1400psi to 2000psi / 90bar to 140bar

Flow rate

8.7 Litres/minute

5-7 Litres/minute

For a more visual explanation of how a petrol engine powered jet wash is superior to an electric pressure washer, take a look at this video.

The assembly is straightforward and takes just 5 minutes

  1. Insert the stub axles through the wheels and into the holes in the frame and secure with the R-clips. 
  2. The upper handle inserts into the lower frame and is held in place by spring loaded ball connectors.
  3. Fill the engine with 600ml of SAE30 engine oil supplied. (Do not overfill).
  4. Fill the petrol tank with fresh unleaded petrol. (Do not overfill).
  5. Connect the high pressure hose to the pump and trigger gun with the M22 threaded connectors.
  6. Select the nozzle required and push firmly into the lance quick release fitting.
  7. Connect your garden hose to the pump inlet using the quick release garden hose connector supplied.

How to start a Petrol Power Washer

  1. Check engine oil level (must be to the top of the oil filler neck) and fuel level.
  2. Petrol ON/OFF switch to right (ON)
  3. Choke to left (START)
  4. Throttle to middle position
  5. Turn on mains water supply
  6. Hold in trigger on lance
  7. Pull recoil start firmly until engine starts
  8. Move the choke lever to the right (RUN).

Operating the P3500PWA Petrol Power Washer

Do not run the engine without a water supply connected to the pump. The water acts as a coolant and lubricant for the high pressure pump. If there is no mains water supply connected to the pump, it will overheat the seals and valves and cause permanent damage. Always use fresh mains water. If dirty water is used it can cause damage to the internal parts of the high pressure pump.

The three cylinder high pressure axial pump is fitted with a thermal protection safety valve. If the pressure washer is run without the trigger gun being squeezed open and water flowing through the pump, then the water in the pump will recirculate around the pump and heat up. To prevent the pump from overheating and damaging the seals the thermal protection valve will open and discharge the hot water, which is replaced with fresh cool water. If possible, switch the engine off when not pressure washing. This saves fuel and wear and tear.

Select the required nozzle and be sure to push it firmly into the quick release fitting on the lance. For normal pressure washing hold the nozzle about 30cm from the object being pressure washed. To use the detergent function, place the black nozzle in the lance and the pressure washer will draw the liquid detergent from the built in tank. This is a low pressure nozzle, so when the soap has been applied, change back to the high pressure nozzle to finish cleaning.

The Axial pump is driven by a 212cc 7hp Hyundai OHV engine. The OHV engines benefit from low end torque, fuel-saving and emission-cutting OHV technology and a more compact size when compared to an OHC engine.

Warning

Never point the high pressure lance at people or animals. Never operate this petrol pressure washer indoors or in a confined space as petrol engines produce lethal Carbon Monoxide fumes. Always switch the engine off and allow it to cool before refueling. 

Maintenance

Check the engine oil level daily- it can be filled to the top of the oil filler neck with SAE30 or 15w40 engine oil. Oil filler cap (5.2).

After the first 20 hours, then every 100 hours change the engine oil. There is an engine drain bolt at the bottom of the engine (5.1). Drain into a suitable container and dispose of safely following local guidelines. 

The high pressure pump is a sealed for life, maintenance free unit. Change the air filter and spark plug every 100 hours. Check that there are no leaks in the high pressure hose. Always store in a frost free environment. If there is any water left in the pump and it freezes, it can cause major damage to the pump body.

If storing for more than a few weeks, it is advisable to drain the float bowl on the carburettor. This can be done by switching the fuel off and running the pressure washer for a few minutes until it stops. This will prevent the unleaded petrol going off in the carburettor and make it easier to start on next use.

Notes about buying a petrol pressure washer

Don’t be fooled by huge pressure ratings. We know our stuff. We’ve been in the industry for 15 years and can tell you it’s not possible to obtain more than 3000psi continuous pressure from a 6.5hp 196cc to 7hp 212cc engine fitted with an axial pump, unless the flow rate is reduced to such a low level that it is not efficient in real life use. Other sellers may claim a lot higher pressure ratings. Please be careful when selecting your pressure washer. 

 

WARRANTY

This product is covered by a manufacturer warranty of 2 years.



SPECIFICATIONS

Gross Weight (kg) 31.50
Engine Size 212cc
Starting System Recoil
Max Pressure 2990psi/206bar
Flow Rate 8.7L
Box Dimensions H x W x L 549 x 520 x 600
Fully Assembled Dimensions H x W x L 1000 x 500 x 600
Model P3500PWA
Net Weight 31.50


Free delivery on orders over £20.00. 

* Delivery to Ireland and N. Ireland is currently unavailable *

FREE UK DELIVERY 
All our products except car batteries are available for free UK delivery when you spend £20 or more. 

STANDARD UK DELIVERY 
Standard UK delivery available from £3.99 for orders below £20.00. 

FREE SAME DAY SWANSEA DELIVERY
Free delivery same day in Swansea when you spend over £20.

CLICK & COLLECT
Free click and collect from our store in Swansea. Simply make your purchase through the website and select the Click & Collect option at checkout.

UK NEXT DAY DELIVERY 
Next day delivery available in the UK for £6.99 if ordered before 1pm. 
Please note Next Day may not always be available for our entire product range.


 DELIVERY TIME

Location *Estimated Shipping Time
England 3-5 working days
Wales 3-5 working days
Scotland 3-5 working days
Channel Islands & Highlands 4-8 working days

 

We provide Free UK delivery on all products except for our car batteries. We are based in the UK and all of our items are shipped from our fulfilment centres. We have over 80,000 product lines available for same day delivery and over 2,000 power and construction equipment ready for collection or fast delivery. 

Please also allow 3 - 5 days for our free UK delivery option or standard delivery, depending on your location. Orders are often delivered well before the estimated arrival date and we will keep you updated along the whole process. Next day delivery is available from £6.99. Please note UK NEXT DAY may not always arrive the next day as this can vary on location. 

Tracking information will be provided with an order confirmation email. Sometimes tracking information may not appear for 1-3 days during which time your order is being processed. You may contact us at any time. We are here for you 24 hours a day, 7 days a week. You can contact us: 
Sales department: sales@hwbcarparts.com
Customer Services: aftersales@hwbcarparts.com
Trade/Wholesale: accounts@hwbcarparts.com
Telephone: 01792 278454
Live Chat: here

Please note that delivery to Scottish Highlands and islands such as Jersey, Guernsey and Isle of Wight will be subject to additional delivery costs. We will get in touch with you before processing your order. If you would like to enquire about the price of these locations before hand please get in touch with us via email or telephone and we can help with this.

If we are unable to temporarily or permanently deliver to your location we will contact you and/or cancel the order, issuing a full refund. Check your delivery options correctly at the checkout.


RETURNS
Our returns policy lasts 30 days. If 30 days has gone by since you received your order, unfortunately we can’t offer you a refund or exchange. You must also contact us within 48 hours of receiving your order if you wish to return or exchange your item(s). Although our returns policy lasts 30 days it is important you contact us immediately (within the 48 hour period of delivery) or we have the right to cancel your refund at any time. You must contact us for a return via email to aftersales@hwbcarparts.com to log the date and time of the report or we reserve the right to reject your return. 

To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging. 

To complete your return, we require a receipt or proof of purchase. 
Please do not send your purchase back to the manufacturer. 

If 30 days has gone by since delivery of any product the customer is only eligible for a repair or replacement under warranty and not a refund. 

We provide free UK returns for power equipment and construction products. If your purchase falls outside this category such as car parts, accessories, lubricants, oils etc you are liable to pay for the return. 

To start a return
Simply visit our returns centre here.

There are certain situations where only partial refunds are granted (if applicable) 
- Any item not in its original condition, is damaged or missing parts for reasons not due to our error 
- Any item that is returned more than 30 days after delivery 
- No contact was made to us within 48 hours of delivery with refund request

Refunds (if applicable) 
Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. We will also notify you of the approval or rejection of your refund. 
If you are approved, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within 3-5 working days.

Late or missing refunds (if applicable) 
If you haven’t received a refund yet, first check your bank account again. 
Then contact your credit card company, it may take some time before your refund is officially posted. 
Next contact your bank. There is often some processing time before a refund is posted. If you’ve done all of this and you still have not received your refund yet, please contact us at aftersales@hwbcarparts.com or live chat. 

Sale items (if applicable) 
Only regular priced items may be refunded, unfortunately sale items cannot be refunded. 

Exchanges (if applicable) 
We only replace items if they are defective or damaged. If you need to exchange it for the same item, send us an email at aftersales@hwbcarparts.com or live chat on our website.

Gifts 
If the item was marked as a gift when purchased and shipped directly to you, you’ll receive a gift credit for the value of your return. Once the returned item is received, a gift certificate will be mailed to you. 

If the item wasn’t marked as a gift when purchased, or the gift giver had the order shipped to themselves to give to you later, we will send a refund to the gift giver and he will find out about your return. 

Shipping 
To return your order, please contact us and we will provide further information on how to send it back to us. 

You will be responsible for paying for your own shipping costs for returning non-power equipment products. Our power and construction products will be collected free of charge. Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund. 

Depending on where you live, the time it may take for your exchanged product to reach you, may vary. 

If you are shipping an item over £75 that is not power equipment category, you should consider using a trackable shipping service or purchasing shipping insurance. We don’t guarantee that we will receive your returned item.

CANCELLATION POLICY & CHANGE OF MIND
In the event that you would like to cancel your order with us, you must notify us within 12 hours of placing the order or the item could be already dispatched. Additionally, if you wish to cancel your order, there will be a 10% restocking and administration fee which will be deducted from your refund. If you would like to return your item because of change of mind, you may also be subject to the 10% restocking and administration fee. If you have any questions regarding cancelling or returning your order please email sales@hwbcarparts.com or call us on 01792 278454 and our team will be happy to help. 

If your order has been cancelled by us due to delays, incorrect stock or administration errors on our end, then there will be no restocking or administration charges. 

WARRANTY POLICIES 
Please note products under warranty are manufacturer warranties and not directly handled by us. While we do manage the whole warranty aspect for you and liaise with the manufacturers on your behalf to speed up the process, the warranty guidelines themselves are set out by the manufacturer in question. Each manufacturer has their own warranty terms and guidelines. You can find out about our manufacturer warranties below: 

1) Hyundai Power Products. 
Warranty information here. 

2) Champion Power Equipment
Warranty information here. 

3) Scheppach 
Warranty information here. 

4) Altrad Belle
Warranty information here.